Basic Technology Second Term Continous Assessment Test Questions 2019/2020 Session – Junior Secondary School (JSS 1,JSS2, JSS 3)

                EDUDELIGHT SECONDARY SCHOOL

1 BENSON AVENUE, LEKKI PHASE 1, LAGOS.

SECOND TERM FIRST CAT 2019/2020

SUBJECT:BASIC TECHNOLOGY  CLASS:JSS1             TIME:40 MIN

OBJECTIVE: Answer all questions.

1.These devices are for fire protection except one. (a)portable fire extinguishers (b)sand buckets (c)fire alarm system (d)asbestos.

2.Example of physical human behaviour is……(a)carelessness (b)improper tool (c)colour blindness (d)mishandling of machines.

3.Which of the following is not a property of metals?(a)brittleness (b)colouration (c)density (d)elasticity.

4.Which of the following is not a ferrous metal?(a)alloy steel (b)cartridge brass (c)white cast iron (d)malleable cast iron.

5.Metals are basically classified into….. and…….. (a)ferrous,non ferrous (b)sheet,base (c)ductile,hard (d)malleable,ferrous.

6.Supermarket house can be regarded as a….. building  (a)commercial (b)residential (c)public (d)industrial.

7.Concrete is made of cement,water,gravel and……. (a)clay (b)mud (c)silica sand (d)stone.

8.Drawing papers are mounted on the drawing board with the aid of……. And……(a)compass,clip pins (b)protractor,set square (c)set square,T-square (d)T-square,dividers.

9. The part of a building where air comes in is…….. (a)window (b)door (c)floor (d)roof.

10.Bungalow house can be classified under……..(a)industrial buildings (b)residential buildings  (c)commercial buildings (d)public buildings.

SECTION B THEORY

1.What is building?List five compartments of building and explain one.

2.List five building materials and state the importance of one.

                   EDUDELIGHT SECONDARY SCHOOL

1 BENSON AVENUE, LEKKI PHASE 1, LAGOS.

SECOND TERM SECOND CAT 2019/2020

SUBJECT:BASIC TECHNOLOGY  CLASS:JSS1             TIME:40 MIN

OBJECTIVE: Answer all questions.

1.Concrete is made of cement,water,gravel and…….(a)clay (b)mud (c)silica sand (d)stone.

2.Lines used to represent visible outlines and edges are….(a)thick continuous (b)thick long-chain (c)thin dashes (d)thin continuous.

3.Which of the following angles cannot be drawn without a protractor?(a)250 (b)300 (c)1350 (d)600.

4.Elasticity is a character of ….(a)ceramic (b)cement (c)plastic (d)rubber.

5.All are important parts of a building except…(a)roof (b)floor (c)window (d)lintel .

6.The type of soil with a stony nature is called……(a)sharp sand (b)soft sand (c)mudy sand (d)loamy sand.

7.There are ….. type of sand. (a)3 (b)2 (c)5 (d)6.

8.There are two types of the Tee-square,which are….(a)plain and scale (b)scale and lent (c)lent and plain (d)normal and smooth.

9.One example of renewable energy source is…..(a)sun (b)coal (c)natural gas (d)kerose

10.The part of the building that carries all superimposed load is..(a)roof (b)floor (c)foundation (d)lintel

   SECTION B.

1.What is drawing instrument? List five drawing instrument and explain their use

2.Draw three examples  of drawing instruments.

               

EDUDELIGHT SECONDARY SCHOOL

1 BENSON AVENUE, LEKKI PHASE 1, LAGOS.

SECOND TERM FIRST CAT 2019/2020

SUBJECT:BASIC TECHNOLOGY  CLASS:JSS2             TIME:40 MIN

OBJECTIVE: Answer all questions.

1.Each angle of a square is……..(a)45 (b)60 (c)90 (d)180.

2.A regular polygon with nine sides is called a/an………….(a)hexagon (b)heptagon (c)octagon (d)nonagon.

3.Division of a line into two equal parts is known as…..(a)bisection (b)computation (c)construction (d)trisection.

4.A pentagon has…….sides.(a)3  (b)4  (c)5  (d)6

5.The following are quadrilaterals except..(a)kite (b)rectangle (c)rhombus

(d)square.

6.The three intersecting lines of the isometric axes meet at a point called the…..(a)varnishing point (b)origin (c)right angle (d)angle of projection.

7.A regular polygon with nine sides is called…(a)hexagon (b)decagon (c)heptagon (d)nonagon.

8.To measure and draw various angles you need a….(a)template (b)set-square (c)protractor (d)French curve.

9.A trapezium is also a….. (a)triangle (b)parallelogram (c)pentagon quadrilateral.

10.Drawing paper is placed squarely on the drawing board with the aid of…(a)tee-square (b)scale rule (c)ruler (d)hands.

           SECTION B  (THEORY)

1.What is a quadrilateral?List all examples of quadrilateral.

2.Construct an hexagon using radius value of 4cm.

             

EDUDELIGHT SECONDARY SCHOOL

1 BENSON AVENUE, LEKKI PHASE 1, LAGOS.

SECOND TERM FIRST CAT 2019/2020

SUBJECT:BASIC TECHNOLOGY  CLASS:JSS3             TIME:40 MIN

OBJECTIVE: Answer all questions.

1.The blast furnace is used for manufacturing…………..(a)aluminium (b)lead (c)pig iron (d)metal sheet.

2.The following are artificial wood defect except………(a)bow (b)check (c)knot (d)cup .

3.If a 90g piece of timber weighs 60g when completely dried,the dried moisture content is….(a)30 (b)50 (c)125 (d)45.

4.The process of reducing moisture content in wood is known as…..(a)conversion (b)felling (c)seasoning (d)veneering.

5…………… is a drawing that shows the arrangement of rooms in a building when viewed from above ground level. (a)elevation drawing (b)building plan (c)isometric drawing (d)oblique drawing.

6.Examples of fittings are these except…..(a)hinges (b)locks (c)catches (d)nails.

7.In mortise and tenon joint,the piece member that contains tenon is called…..(a)rail (b)stile (c)mortise (d)halving.

8.Examples of common wood finishing materials are these except…..(a)varnishes  (b)lacquers (c)polishes (d)creosote.

9.These are types and makes of locks except…(a)box lock (b)drawer lock (c)book lock (d)cupboard lock.

10.Thes are methods of joining metal pieces…..  (a)Tanning (b)welding (c)soldering (d)riveting.

SECTION B. 

1.What is woodwork project?List four woodwork tools.

2.List five types of roof and state two functions of a wall.

               

EDUDELIGHT SECONDARY SCHOOL

1 BENSON AVENUE, LEKKI PHASE 1, LAGOS.

SECOND TERM SECOND CAT 2019/2020

SUBJECT:BASIC TECHNOLOGY  CLASS:JSS3             TIME:40 MIN

OBJECTIVE: Answer all questions.

1.Dodecagon is a polygon with….. sides.(a)11 (b)12 (c)23 (d)13.

2.The drawing instrument used for drawing irregular curves is called…(a)bow compass (b)protractor (c)French curve (d)set-square.

3.Which of the following instrument is used for free hand sketching?(a)pencil and eraser (b)set-square and pencil (c)tee-square and pencil (d)compass and pencil.

4.Which of the following can be used for drawing vertical and inclined lines? (a)protractor (b)scale rule (c)compass (d)set squares.15…… is the machine most commonly used for turning operations.(a)lathe machine (b)shaping machine (c)milling machine (d)drilling machine.

6.A trapezium is also a……(a)triangle (b)quadrilateral (c)pentagon (d)parallelogram.

7.The pair of compasses is used for drawing….(a)vertical and inclined lines (b)irregular curves and angles (c)horizontal and parallel lines (d)arcs and circular lines.

8.One of these is a type of woodwork machine.(a)wheel barrow (b)semi circular machine (c)saw machine (d)wood tool machine,

9.Which of the following is not a quadrilaterals?(a)prism (b)rhomboid (c)rhombus (d)parallelogram.

10.A regular polygon with five sides is ….(a)pentagon (b)heptagon (c)hexagon (d)cyclegone.                   SECTION B

1.What is metal finishing?State five reasons for finishing.

2.List woodwork project and explain two.

             

  EDUDELIGHT SECONDARY SCHOOL

1 BENSON AVENUE, LEKKI PHASE 1, LAGOS.

SECOND TERM SECOND CAT 2019/2020

SUBJECT:BASIC TECHNOLOGY  CLASS:JSS2             TIME:40 MIN

OBJECTIVE: Answer all questions.

1.Which of the following is the shape of the figure shown below? (a)kite (b)parallelogram (c)rectangle (d)rhombus,

2.Which of the following is the name of the shape shown below.(a)cone (b)square (c)prism (d)sphere.

3.The following are quadrilaterals except..(a)kite (b)rectangle (c)triangle (d)square.

4.Which of these is used to hold a job on the drill press? (a)drill chuck (b)cellotape (c)vice (d)headstock.

5. triangle can be constructed with the following except…(a)three sides given (b)three angles given (c)two sides and altitude given (d)one side and two base angles given.

6.The ability of a soil to carry load is called….capacity.(a)power (b)load (c)strength (d)bearing.

7.W can take care of our drawing board by ….(a)keeping it inside the locker (b)keeping it on the floor (c)washing with soap and water when dirty (d)avoiding scratches on the surface.

18.A polygon with eleven sides is called…(a)undecagon (b)decagon (c)pentagon (d)dodecagon.

9.The sum of angles in a square is…..(a)180 (b)360 (c)90 (d)120.

10.Dodecagon is a polygon with….. sides.(a)11 (b)12 (c)23 (d)13.

                 THEORY (SECTION) B

1.Show the construction ofn the following;

        a.parallelogram   b.trapezium  c.rhoboid.

Lessonplan

Get Lesson plans, Lesson notes, Scheme of work, Exam Questions, Test Questions for all subject for Primary school and Secondary School.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
Share via
Share
Close
Close

Adblock Detected

Please, Disable Adblock to access this website.
error: Please, enable javascript
Thanks for the kind gesture
Please Like and follow us